1. Apc 1500 Smart Ups Manual Review
2. Smart Ups 1500 Battery Replacement
3. Apc 1500 Smart Ups Manual User
4. Apc Smart Ups 1500 Xlm Manual

Read and download APC Power Supply BACK-UPS PRO 1500 User's Manual online. Download free APC user manuals, owners manuals, instructions, warranties and installation guides, etc.

English

APC Smart-UPS®

750/1000/1500 VA

100/120/230 Vac

2U Rack-Mount

Uninterruptible Power Supply

990-1194C07/2008

Introduction

The APC Uninterruptible Power Supply (UPS) is designed to prevent blackouts, brownouts, sags, and surges from reaching your computer and other valuable electronic equipment. The UPS filters small utility line fluctuations and isolates your equipment from large disturbances by internally disconnecting from the utility line. The UPS provides continuous power from its internal battery until the utility line returns to safe levels or the battery is discharged.

1:INSTALLATION

Read the Safety Instruction sheet before installing the UPS.

Unpacking

Inspect the UPS upon receipt. APC designed robust packaging for your product. However, accidents and damage may occur during shipment. Notify the carrier and dealer if there is damage.

The packaging is recyclable; save it for reuse or dispose of it properly.

Check the package contents. The package contains the UPS, the front bezel, the rail kit, and a literature kit containing:

•Product documentation and safety information

•CD-ROMwith additional user manual language support and safety information

•PowerChute® CD-ROM(120V/230V models only)

•Serial and USB communication cables

•Two IEC jumper cables and one plug adaptor (230V models only)

The UPS is shipped with the battery disconnected.

Rail Installation

Install the rails following instructions in the rail kit.

Mounting rails are supplied for the standard 4-postrack.Two-postracks require only the mounting brackets.

13

1

Positioning the UPS

Place the UPS where it will be used. The UPS is heavy. Select a location sturdy enough to handle the weight.

Do not operate the UPS where there is excessive dust or the temperature and humidity are outside the specified limits.

0º40ºC (32º-104ºF)

PLACEMENT 0-95%Relative Humidity 2.5 cm (1 in.)

Mounting the UPS in a Rack

The UPS is heavy. To lighten it, you may remove the battery before mounting the unit in the rack (Steps 1 and 2).

Step 3

Install the UPS at or near the bottom of the rack (Step 3).

Check to ensure the rack will not tip after installing the UPS into the rack.

2

Installing and Connecting the Battery and Attaching the Front Bezel

Connect battery plug to UPS. Tuck white battery cord into space above connector.

Connecting Equipment and Power to the UPS

SMART-UPS REARPANEL

100/120V Models

120V Model Only: Site wiring fault indicator

230V Models

3

1.Connect equipment to the UPS. Note: Do not connect a laser printer to the UPS. A laser printer draws significantly more power than other types of equipment and may overload the UPS.

2.Add any optional accessories to the Smart-Slot.

3.Using a power cord, plug the UPS into a two-pole,three-wire,grounded receptacle only. Avoid using extension cords.

100V/120V models: The power cord is permanently attached to the rear panel of the UPS. The INPUT plug is a NEMA5-15P.

230V models: The power cord is supplied by the customer. Connect ground leads to the TVSS screw (optional). To make the connection, loosen the screw and connect the surge suppression device’s ground lead. Tighten the screw to secure the lead.

4.Turn on all connected equipment. To use the UPS as a master ON/OFF switch, be sure all connected equipment is switched ON. The equipment will not be powered until the UPS is turned on.

5.To power up the UPS press the button on the front panel.

•The UPS charges its battery when it is connected to utility power. The battery charges to 90% capacity during the first four hours of normal operation. Do not expect full battery run capability during this initial charge period.

•120V Models: Check the site wiring fault LED located on the rear panel. It lights up if the UPS is plugged into an improperly wired utility power outlet. Refer toTroubleshooting in this manual.

6.For additional computer system security, install PowerChute® Smart-UPSmonitoring software.

BASICCONNECTORS

Use an APC supplied cable to connect to the Serial Port. DO NOT use a standard serial interface cable since it is incompatible with the UPS connector.

Both Serial and USB Ports are provided. They cannot be used simultaneously.

TVSS Screw The UPS features a transient voltage surge-suppression(TVSS) screw for connecting the ground lead on surge suppression devices such as telephone and network line protectors.

When connecting grounding cable, disconnect the UPS from utility power.

Apc 1500 Smart Ups Manual Review

4

SMART-UPS FRONTPANEL

Power On

Power Off

This LED illuminates to indicate the UPS is compensating for a high utility voltage.

This LED illuminates to indicate the UPS is compensating for a low utility voltage.

When the on battery power LED is lit the UPS is supplying battery power to the connected equipment. When on battery, the UPS sounds analarm—fourbeeps every 30 seconds.

The LED illuminates and the UPS emits a sustained alarm tone when an overload condition occurs.

5

Replace Battery

Battery

Disconnected

Automatic Self-Test

Manual Self-Test

Failure of a battery self-testcauses the UPS to emit short beeps for one minute and thereplace battery LED illuminates. Refer toTroubleshooting in this manual.

The replace battery LED flashes and short beep is emitted every two seconds to indicate the battery is disconnected.

The UPS performs a self-testautomatically when turned on, and every two weeks thereafter (by default).

During the self-test,the UPS briefly operates the connected equipment on battery.

If the UPS fails the self-test,thereplace battery LEDlights and immediately returns to online operation. The connected equipment is not affected by a failed test. Recharge the battery for 24 hours and perform anotherself-test.If it fails, the battery must be replaced.

Press and hold the button for a few seconds to initiate theself-test.

On Battery Operation

The Smart-UPSswitches to battery operation automatically if the utility power fails. While running on battery, an alarm beeps four times every 30 seconds.

Press the button (front panel) to silence the UPS alarm (for the current alarm only). If the utility power does not return, the UPS continues to supply power to the connected equipment until the battery is exhausted.

If PowerChute® is not being used you must manually save your files and turn off the computer before the UPS fully discharges the battery.

DETERMININGONBATTERYRUNTIME

UPS battery life differs based on usage and environment. It is recommended that the battery/batteries be changed once every three years. See the APC web site, www.apc.com, for on battery run times.

6

3:USERCONFIGURABLEITEMS

NOTE: SETTINGS ARE MADE THROUGH SUPPLIEDPOWERCHUTE SOFTWARE OR OPTIONALSMARTSLOT

ACCESSORY CARDS.

7

NOTE: SETTINGS ARE MADE THROUGH SUPPLIEDPOWERCHUTE SOFTWARE OR OPTIONALSMARTSLOT

ACCESSORY CARDS.

8

• #
  28.07.20151.86 Mb6User Manual 3.pdf

English

APC Smart-UPS

1500/3000 VA 120/230 Vac

Modular

Uninterruptible Power Supply

990-170401/2004

Introduction

This APC Smart-UPSis a modular Uninterruptible Power Supply (UPS) for high availability applications such as data centers and mission critical processes, designed to prevent blackouts, brownouts, sags, and surges from reaching your equipment. The UPS filters small utility line fluctuations and isolates your equipment from large disturbances by internally disconnecting from the utility line. The UPS provides continuous power from its internal battery until the utility line returns to safe levels or the battery is fully discharged.

1: INSTALLATION

Smart Ups 1500 Battery Replacement

The User Manual and Safety Guide are accessible on the supplied User Manuals CD and on the APC web site, www.apc.com.

Unpack

Attention: Read the safety instruction sheet before installation.

Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly. Check the package contents:

UPS

Bezel

Tower conversion top panels and mounting stabilizers

Rail kit

UPS literature kit containing:

Position the UPS in the Specified Environment

0-40°C

0-95%

1

Mount the UPS in the Rack and Connect the Battery

Attention: Install the rails following the instructions in the rail kit.

2

Tower Configuration

Press and hold the black switch (see location

designation on UPS) to the right while removing the power processing module.

Snap the display bezel out the rear to begin rotation.

Note: Place the UPS in the final operating location prior to module reinstallation.

Rear

3

2: START UP

Connect Equipment to the UPS

Note:

•The ‘outlet groups’ can be controlled through the network software. See Network Management Card documentation.

•A laser printer draws significantly more power than other types of equipment and may overload the UPS.

Connect the UPS to the Network (if Applicable)

Note:

•Use only the supplied cable to connect to the Serial Port. A standard serial interface cable is incompatible with the UPS. Serial and USB ports cannot be used simultaneously.

•If an optional Smart-Slotaccessory is to be used, remove the preinstalled network management card and install it now.

Start the UPS

Attention: Upon utility power connection, the UPS will automatically turn on.

1.Plug the UPS into a two-pole,three-wire,grounded receptacle only. Input Plugs:

1500 VA models: 120 V = NEMA5-15P;230 V = Use country specific 10 A with C14 input cords (not supplied).

3000 VA models: 120 V = NEMAL5-30P;230 V = Use the supplied cords or the country specific equivalent.

4

The battery will charge to full capacity during the first few hours of normal operation. Do not expect full ‘on battery’ capability during this initial charge period.

Apc 1500 Smart Ups Manual User

2.After the UPS has ended the immediate self-testwithonline LED illumination, check the front display for any fault indicators (seeTroubleshooting).

3.120 V models: Check thesite wiring fault LED located on the rear panel. It will be illuminated if the UPS is plugged into an improperly wired utility power outlet (seeTroubleshooting).

4.Turn on all connected equipment. To use the UPS as a master on/off switch, be sure all connected equipment is on.

Equipment is now powered and protected. Basic operation, user configuration, and software utilization can now be performed as required.

Battery Operation

The UPS switches to battery operation automatically if the utility power fails. While running on battery, an alarm beeps four times every 30 seconds. Press the button to silence this alarm.

If the utility power does not return, the UPS continues to supply power to the connected equipment until the battery is fully discharged.

Refer to www.apc.com for battery runtime charts.

When the UPS reaches the low battery shutdown warning (two minute default), the alarm will beep continuously until total shutdown. Connected equipment should be shut down during this time, unless being controlled by network monitoring software.

5

3:BASICOPERATION

Front Display Panel

6

7

Apc Smart Ups 1500 Xlm Manual

4:USERCONFIGURABLEITEMS

NOTE: SETTINGS ARE MADE THROUGH THE SUPPLIEDPOWERCHUTE SOFTWARE OR

THE NETWORK INTERFACE CONNECTION. REFER TO THE SOFTWARE HELP GUIDES FOR DETAILS.

8